B-DETECTION MOBILE gas measuring system for high-pressure applications

B-DETECTION MOBILE breathing air and gas measuring systems
B-DETECTION MOBILE breathing air and gas measuring systems

In addition to continuous stationary monitoring of CO2, CO and O2 in the compressor, this device uses a pressure reducer to allow mobile analysis of breathing air on site. There is also the option of measuring the dew point and thereby displaying the absolute humidity in accordance with DIN EN 12021:2014.

Packaged inside a sturdy plastic­ case and equipped with a powerful battery for standalone operation.

If the measuring system is used for continuous measurement with a compressor with B-CONTROL, the measured values can be saved with the B-CONTROL data logger and downloaded to a computer easily via SD card (B-CONTROL MICRO) or USB stick (B-CONTROL II) for output in Excel.

All the information you need at your fingertips!

More features of breathing air and gas measuring systems for high-pressure compressors:

External outputs and alarm output are watertight to allow outdoor operation in wet or humid conditions

Alarm and error messages when predefined limit values as per DIN EN 12021:2014¹ are exceeded

Operation and charging require standard 110/220 V power source

Designed for connection to 12/24 V on-board electrical systems

PureAir/PureAir GOLD Certification possible (for continuous operation)

¹ No residual oil measurement, compliance monitoring of humidity limit values by choosing absolute humidity measurement only.

Humidification distance
Electrochemical sensors (CO and O2) require a certain level of gas quality in terms of humidity, pressure and temperature to ensure they function to their full potential. In fact, if the gas treatment is incorrect or even lacking, this can significantly reduce the service life of the sensors. For this reason, if the B-DETECTION is in continual use for over an hour, BAUER recommends the use of an optional humidity membrane to ensure the sensors are able to run to maximum capacity.

Pressure reduction unit with solenoid valve
Pressure reduction unit with solenoid valve

Pressure reduction unit
The pressure reduction unit allows the measuring instrument to be connected to high-pressure lines. Depending on the control type of the high-pressure compressor, the option of a suitable pressure reduction unit is also available to limit the system inlet pressure with a solenoid valve (for systems with B-CONTROL) or ball valve (hard-wired control). In the case of the solenoid valve option, this is controlled by the compressor unit.

Ambient air pump
Ambient air pump

Ambient air pump
An additional pump installed within the measuring instrument makes it possible to check the gas composition of the intake air. For an overall CO2 content of 430 ppm or more in the intake air, we recommend using an AERO-GUARD CO2 absorber.

CO2 flushing valve
The CO2 concentration in the compressed breathing air within the filter container usually corresponds to the concentration in the ambient air. These values may differ when inserting new filter cartridges (as CO2 is adsorbed from the air by the molecular sieve for a short time) and in the event of a pressure drop within the filter container. If the pressure should drop – which typically happens when switching off each compressor – the CO2 content in the filter container increases. When switching the compressor back on, the accumulated air with its increased CO2 content is then flushed out of the filter container. To avoid increased CO2 values in the compressed breathing air, we recommend flushing the compressor unit – i.e. draining the compressed air to the outside by opening the flushing valve – for approximately 2 minutes before connecting and filling the compressed air cylinders. As not all high-pressure compressors have a flushing valve for discharging increased CO2 values included in the standard scope of delivery, BAUER offers the option to retrofit this type of equipment.

Automatic bleed unit
The bleed unit allows compressor units to flush automatically by redirecting compressed air into the surrounding atmosphere.
If the CO2 values in the compressed air are too high during the compressor start phase, B-DETECTION is suppressed from switching off the compressor and the compressed air is routed into the surrounding atmosphere via a silencer for a fixed period. If there is still no improvement in the air values several minutes, the compressor then switches off.

B-DETECTION MOBILE breathing air and gas measuring systems
  Carbon dioxide (CO2), carbon monoxide (CO), Oxygen (O2)
Measurement Ambient
  0 – 420 barg (6100 psig) (pressure range options)
CO2 Nondispersive infrared spectroscopy (NDIR)
CO, O2 Electrochemical
Humidity Capacitive (only using B-SECURUS) or via dew point sensor (as option)
CO2 0 ppm (parts per million)
CO 0 ppm
O2 0.1 %
CO2 0 ... 5000 ppm
CO 0 ... 30 ppm
O2 0 ... 50%
CO2 ± 10 % FS (full scale)
CO ± 5 % FS
O2 ± 2 % FS
Alarms Alarm when one or more limit values is exceeded
Operating voltage 12 V DC
Power consumption Max. 36 W
Dimension W × H × D [mm]
(w/o connection and accessories)
Mobile: 250 × 305 × 135
Visual inspection and leak test once a month
Functions check ¹ at least every three month
System check ² once a year
Calibration CO2 sensor before commissioning, after replacing the sensor; dew point sensor: every two years

¹ Including test with test gas; corresponding kit containing test gas cylinders and pressure reducer (flow meter) available from BAUER KOMPRESSOREN.

² The system check includes replacing the electrochemical sensors (CO and O2 ).

Downloads for the B-DETECTION MOBILE gas measuring system for high-pressure applications

BAUER Accessory Systems – The ideal enhancement to your compressor

Go to Download Centre

Videos for the B-DETECTION MOBILE online gas measuring system for high-pressure applications

Show all BAUER films